Knud Bro Allé 4
+45 44 84 37 56

Zyvax – release agents

Cleaners

SURFACE CLEANER

SOLVENT BASED​

Description:

SURFACE CLEANER Fis a combination of solvents specially blended to aid in the preparation of new and used moulds/tools prior to treatment with Zyvax Mould Sealer and Release Agents. It readily removes waxes and other surface contaminants without harming or dulling the working surfaces of the mold.

​SURFACE CLEANER will also clean brushes and spay equipment used to apply various release products and elastomeric materials. (For NON-VOC cleaner please refer to WATER CLEAN or Granudan Cleaner GR-08)

Sealers

SEALER GP​

SOLVENT BASED​

Description:

SEALER GP is a high modulus, clear, flexible film with subtrate adhesion that forms a protective shield on the mould or tool surface. As a conditioner, SEALER GP is designed to treat both the chemical and physical bonding sites found on every “raw” mould surface.

In addition, SEALER GP provides the base needed to extend the life of the release coating and will allow optimal performance from the release coating.( For NON-VOC Sealer please refer to BREEZ SEALER BN201)

Release agents

SLIPCOAT NR: 1 MULTI SHIELD

SOLVENT BASED​

Description:

Medio highgloss, very high release power

MULTI SHIELD is a high performance, general purpose, semi-permanent release coating. It offers effective multiple release efficiency with a wide range of moulding compounds- especially vacuum-injection, hot press, and for demouldings with a high release-difficulty.(For NON-VOC release agent please refer to WATER SHIELD)​

SLIPCOAT NR:2 FIBERGLASS SHIELD

SOLVENT BASED​

Description:

High gloss, high release power

FIBERGLASS SHIELD is a high performance, semi-permanent release coating specially formulated to provide high gloss mouldings of polyester resins and gelcoats.

It also offers effective multiple release efficiency with a wide range of moulding compounds – especially boat-moulds, vacuum-injection, cultured marble, and for moulds with some release-difficulty. (For NON-VOC release agent please note ENVIROSHILD)

SLIPCOAT NR:3 COMPOSITE SHIELD

SOLVENT BASED

Description:

Medio high gloss, medio high release power

COMPOSITE SHIELD is a high performance, semi-permanent release coating specially formulated for use with advanced moulding materials in industries requiring assured contamination free fail-safe processing.

​It also offers effective multiple release efficiency with a range of compounds – especially large boat-moulds, windmill houses, and for moulds where a high release IS NOT necessary.

Release agents – FLEX-Z wipe-on/leave-on:

No wiping-off – just apply and wait for curing in 15 minutes. Can be applied with spray-gun. Very flexible, and very easy to use!

NOTE: Just two coats of Sealer GP is recommened before use. – Quick change of release power with 6 different variations.

Flex-Z allows the moulder to apply the exact level of release performance needed over an entire mould, or in each specific area of ANY mould or process. Flex-Z eliminates general problems as pre-release, shrinkage and streaking from the traditional Semi-permanent Release system. The Flex-Z product applied latest decides release level. A suggestion is to apply no. 3.0 or 4.0. on entire mold, and then adjust the release power afterwards on critical areas.

Flex-Z datasheet!

FLEX-Z NO. 1

SOLVENT BASED​

Description:

FLEX-Z NO. 1 MINIMUM SLIP

Inhibits pre-release and promotes tape adhesion..

FLEX-Z NO. 2

SOLVENT BASED​

Description:

FLEX-Z NO. 2 LOW / MEDIUM SLIP

​Ideal for the occasional pre-release problem.

FLEX-Z NO. 3

SOLVENT BASED​

Description:

FLEX-Z NO. 3 MEDIUM SLIP

​Standard choice for large hulls and flat areas. .

FLEX-Z NO. 4

SOLVENT BASED​

Description:

FLEX-Z NO. 4 Medium / high slip

””Workhouse” – If you are in doubt, start here.

FLEX-Z NO. 5

SOLVENT BASED​

Description:

FLEX-Z NO. 5 High slip

Excellent choice for small parts and high wear areas

FLEX-Z NO. 6

SOLVENT BASED

Description:

FLEX-Z NO. 6 Very high slip

Use in difficult-to-release male moulds or as flange release

Product description

Zyvax was the first company in the release business to introduce an easy to use and reliable, one part, room temperature curing range of Waterbased Semi-permanent Release Agents.

Industries:

​Aeronautics & Aerospace, Automotive, Marine, Mass Transportation, Sports & Leisure, Wind Energy, Other sectors, Ancillary Products.

Prod. methods:

– Epoxy /polyester pre-preg
– Epoxy / polyester infusion
– Others..

The traditional solvent-based coats are of course stronger (more durable and resilient) than the waterbased solvent-free products, and give our customers a higher yielding capacity, meaning more de-mouldings before re-application is necessary. The Semi-Permanent, solventbased Release Agents are Thermal stabile up to 480 C., which increases the possibility for the use of release coats in many different production-environments. Zyvax Release System is based on special formulated polymers, which cures on the surface of the mould; therefore no build-up or transfer of slipcoat will occur – unlike systems containing Wax or Silicones.

The Zyvax release agents have earned the highest awards among users throughout the industries they have been introduced to.

Why Zyvax

  • Less consumption
  • 1 liter covers approx. 130m2
  • Quick curing – 15 min.​
  • Easy application.
  • Very efficient
  • consistent, reliable performance.
  • Cost per part significant less.
  • Environment, safety ​​