GRANUDAN RELEASE AGENT SYSTEMS

BreeZ Waterclean is a water-based cleaner and an effective alternative to solvent based products

BreeZ Waterclean effectively removes everything! – both sealer, release agents etc. The product is ideal for preparing surfaces for paint or other processes that requires a totally clean surface

The product should be used with water and may not dry out on surfaces. We recommend using water for removal

4 liters

Item no.:
ZYWATCL003

Download Datasheet

Cleaner GR-08 is effective, environmentally friendly and an alternative to solvent based products

This water-based cleaner is an effective degreaser and removes surface contamination such as oil, wax, soap, and dust from sanding. It will not remove sealer or release agents

Water can be added to this product

5 liters

Item no.:
GR08003

Download Datasheet

BreeZ Surface Cleaner effectively removes waxy release agents, polishing pastes, styrene build-up, and impurities. The product does not remove sealer

Use this product before the first layer of release coats. The product can also be used for cleaning brushes and other equipment

4,75 liters

Item no.:
ZYSUR-EU-4,75

Chemlease Mold Cleaner EZ is a blend of solvents designed for removal of wax and contaminants from composite molds

Apply with 100% cotton cloths before the first layer of release coats. The product is also excellent for cleaning brushes and equipment

3,8 kg

Item no.:
1125370225

Extremely efficient solvent based cleaner for removal of waxes, oils and other contaminations. High content of hazardeus materials. Contains Toluene! Only sold in EU.

1 or 5 liters

Item no.:
050363

A primer is the perfect solution for plug/master surfaces or if you wish to give a new life to a worn out mold surface

BreeZ MPP 2698W leaves a tough and durable sealed film and overcomes micro-porosity

The product has no release power and an appropriate sealer or release agent should be applied on top of the product after it has cured

3,76 kg

Item no.:
1108380488

Primer MPP 712 EZ is ideal for mold-build (e.g. purfoam) or refurbishment of old, worn mold surfaces. The product has a high viscosity and can bond to almost every surface

The surface needs to be 100 % clean before application of Primer MPP 712 EZ, and a sealer needs to be used afterwards

0,93 kg

Item no.:
1119510530

Water-based sealer designed to treat both the chemical and physical bonding sites found on every mold surface. The product delivers a durable film with superior abrasion resistance. When applied with appropriate semi-permanent release agent, this product provides multiple, effortless releases

5 liters

Item no.:
1262710223

Download Datasheet

BreeZ Sealer BN201 is a water-based alternative to Sealer GP. Developed for use with Zyvax water-based release agent. The product is very durable and suitable in both epoxy, metal, and polyester productions

The product can be applied with both cloth and mop. Together with Watershield and Enviroshield this product is our preferred choice within the Wind Industry

Curing time: 30 min (3-4 coats on composite moulds)

Thermal stability up to 280°C

Approx. 130 sqm./liter.

4 liters

Item no.:
BN201004CT

Download Datasheet

BreeZ Sealproof is a sealer for high porosities, wood, plugs, steel carbon graphite, aluminum, and all types of composites. The product leaves a semi-matte surface and gives a durable, strong, and visible film on both metal, polyester, and epoxy surfaces

Can be spayed and wiped on with cloth – no wiping off

Curing time: 2 hours at 50°C or 12 hours in room temperature at minimum 20°C

Thermal stability up to 280°C

Approx. 100 sqm./liter. (Less with spray-up)

4 liters

Item no.:
ZYSEALPR003

BreeZ Sealer GP overcomes micro-porosity and restores a uniform surface that extends the life of the release coating. For a water-based alternative we recommend BreeZ Sealer BN201

Curing time: 30 min in room temperatures at minimum 20°C (four coats on composite molds)

Approx. 100 sqm./liter.

3,75 liters

Item no.:
ZYSEA003

Chemlease Sealer 15EZ is a high-performance sealer that reduces mold porosity. The product acts as a base for new or reconditioned molds

Item no.:
1116630226 (0,71 kg)

1116630225 (3,5 kg)

Chemlease Matte Sealer 122L has no release properties but the product changes the contour of the surface to matte appearance. Apply one layer of Sealer GP or Sealer EZ after curing

0,8 kg

Item no.:
1132370226

Water-based, semi-permanent release agent specifically formulated to meet the high performance requirements of the Wind Industry by providing consistent, effortless and multiple releases of composites parts. Easy to apply and enviromentally preferred

5 liters

Item no.:
1262690223

Download Datasheet

Watershield is one of our most popular products. The product has a high release power and is perfect for productions with epoxy and no gel coats. Watershield is to be used on molds where the molded parts are more difficult to demold

Curing time: 15 min between applications, 30 min after last application

Thermal stability up to 280°C

Approx. 130 sqm./liter.

Item no.:
ZYWAT003 (4 liters)

ZYWAT001 (19-liter pail w. tap)

Download Datasheet

Enviroshield is one of our most popular products. It has a medio high release power and is suitable for productions with epoxy and use of gel coats. Enviroshield is designed to bigger molds where the molded parts are easy to release

Curing time: 15 min between applications, 30 min after last application

Thermal stability up to 280°C

Approx. 130 sqm./liter.

Item no.:
ZYENV003 (4 liters)

ZYENV001 (19-liter pail w. tap)

Download Datasheet

Granudan Aqua Slipcoat 506 has a high release power. The product is a combination of polymer and liquid wax

The product has high durability on rough materials and complicated molds. Use on both polyesters, vinylester, and epoxy

Curing time: 15 min between applications, 30 min after last application

Thermal stability up to 150°C

Approx. 70-80 sqm./liter.

5 liters (10 liter/box)

Item no.:
AQUA506

Download Datasheet

Chemlease 2196 is a semi-permanent release agent used for FRP composite molding. Ideal for polyester productions

If no sealer is used apply six coats in total

Contains silicone

5 kg

Item no.:
1116430223

Chemlease 2704W provides minimal transfer of release agents, high-temperature stability, high abrasion resistance, and is capable of multiple releases. The product has a medium/low slip and is to be used in polyester and vinylester productions

3,75 kg

Item no.:
1154450493

BreeZ Composite Shield provides a moderate release effect. Used for larger boat molds and for molds where you do not want too good release.

The product prevents pre-release and has a high number of releases

Curing time: 30 min in room temperatures at minimum 20°C

Thermal stability up to 480°C

Approx. 100-130 sqm./liter.

3,75 liters (15 liter/box)

Item no.:
ZYCOM003

BreeZ Multi Shield has a very high slip, and a high number of releases. The product is comparable to Watershield. No buildup. Suitable for polyurethane

Curing time: 30 min in room temperatures at minimum 20°C

Thermal stability up to 480°C

Approx. 100-130 sqm./liter.

3,75 liters (15 liter/box)

Item no.:
ZYMUL003

Fiberglass Shield creates high gloss and has a high release power. Often used on small molds, artificial marble, and molds with low release effect and a wish for high gloss

Curing time: 30 min in room temperatures at minimum 20°C

Thermal stability up to 480°C

Approx. 100-130 sqm./liter.

3,75 liters (15 liter/box)

Item no.:
ZYFIB003

Chemlease 41-90 EZ is a rapid curing semi-permanent mold release agent that provides multiple releases with minimal transfer to the molded part. Primarily for closed molding of abrasive or low draft parts. Use on all mold types

3,4 kg

Item no.
1116670225

Chemlease 75EZ creates high gloss and medium-high slip for polyester productions. This product is a unique semi-permanent mold release system developed specifically for the Composites Industry, for use where a high-quality finish is required

3,4 kg

Item no.:
1116660225

Chemlease 2185 creates high gloss and a medio/low slip. The product is solvent based semi-permanent but contains 1-2% of wax. Can be used on all mold types

Use for small parts and low temperatures. Chemlease 2185 does not require an extended cure

3,4 kg

Item no.:
1034700225

Chemlease 2720 is a semi-permanent release agent for epoxy and polyester productions. The product creates a high slip and high gloss

Chemlease 2720 is fast curing and has multiple releases

3,23 kg

Item no.:
1164150489

Flex-Z 1.0-6.0 is a release agent system for gel coating in six different levels of effectivity. We recommend Sealer GP when you start using Flex-Z. Only apply – do not wipe off. These products are fast curing

3,75 liters

Item no.:
FZ1RSL003: Flex-Z 1.0: MINIMUM SLIP – Inhibits pre-release and promotes tape adhesion

Download Datasheet

Flex-Z 1.0-6.0 is a release agent system for gel coating in six different levels of effectivity. We recommend Sealer GP when you start using Flex-Z. Only apply – do not wipe off. These products are fast curing

3,75 liters

Item no.:
FZ3RSL003: Flex-Z 3.0: MEDIUM SLIP – Standard choice for large hulls and flat areas

Download Datasheet

Flex-Z 1.0-6.0 is a release agent system for gel coating in six different levels of effectivity. We recommend Sealer GP when you start using Flex-Z. Only apply – do not wipe off. These products are fast curing

3,75 liters

Item no.:
FZ4RSL003: Flex-Z 4.0: MEDIUM/HIGH SLIP – If you do not know where to start, start here

Download Datasheet

Flex-Z 1.0-6.0 is a release agent system for gel coating in six different levels of effectivity. We recommend Sealer GP when you start using Flex-Z. Only apply – do not wipe off. These products are fast curing

3,75 liters

Item no.:
FZ6RSL003: Flex-Z 6.0: EXTRA SLIP – Use on difficult-to-release molds or as a flange release

Download Datasheet

INT. 115 is a general-purpose internal release system for epoxy resins for pultrusion process. The product is a liquid internal release system to incorporate directly into the resin to aid in the release process.

Item no.:

Chemlease IC25 is a general-purpose internal release system for most polyester and composite resins. The product is a liquid internal release system to incorporate directly into the resin to aid in the release process. Epoxy/polycarbonat. Be careful with gelcoat – has to be RTM (closed mold)

Item no.:

Polyester Pultrusion. New high-performing chemistry. Good references from US

Item no.:

Chemlease IC60 is primarily used for non-gel-coated polyester resins. When added to polyester resin, it eliminates the need for an external release agent. This product imparts better flow properties to the polyester resin. Pultrution. Be careful with gelcoat – has to be RTM (closed mold)

Item no.:

Polyester. Be careful with gelcoat – has to be RTM (closed mold)

Item no.:

Sacrificial release wax for rigid and flexible polyurethane foams and polyester resins. Works for mold flanges, sealing wood plugs, and other nondensified plug/master surfaces. Thermal stable to 160 C

Item no.:

Sacrificial release wax good for pre-release challenges

Item no.:

BreeZ FLANGE WAX is a well-balanced combination of wax and high-quality lubricants that is especially suitable for application in the flange area of polyester applications with vacuum processes

This product enables, besides excellent release properties, a very good adhesion for adhesive tapes and sealing masses on wax films

BreeZ FLANGE WAX is solvent based

0,75 kg (available in boxes with 12 cans)

Item no.:
1132490224

Lusin Alro LL 261 is a silicone-free release agent based on PTFE. Suitable for mould temperatures up to 260°C (500 °F). The white air-drying film adheres to metal, plastic, and glass surfaces and shows excellent release and sliding effects. The high efficiency ensures several release cycles without further application

12 cans of 400 ml in a box

Item no.:
1061810178

Universal release agent for PU and Composites – for molds in complexed designs with unreachable corners and areas.

6 cans of 500 ml in a box

Item no.:

6 cans of 500 ml in a box

Item no.: